Exclusive Heat Drying System

Rapid Structural Drying for Structure, Carpet and Contents 

Please Mention this Service when Calling

We Offer A Exclusive Heat Drying System That Will Dry Out Your House Fast and Will Help Prevent the Potential for Mold and Other Related Problems that Might Arise During the Drying Process

Please Mention this Service when Calling

(Some restriction may apply)

 

Heat Drying Is Perfect for Small Dryouts As Well As Large Dryouts

The Eliminator/ELE 6400 Is Perfect for Smaller Jobs That Don’t Need the Larger Drying Equipment and Still Helps Prevent the Chance of Mold Just Like the Large Drying Systems

Drying System Distributed by;

DRI HEAT

Drying Systems

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

We use these systems to dry carpet, pad, walls, even behind cabinets and showers, etc… without demolition. Reducing damage costs and saving time and Money

Heat Drying

Hardwood Floors

The ELE 6400 is Ducted Up Thru a Floor To Dry the Area Above

Heated Air Directed at Air Mover to Speed Drying Time and Help Prevent Mold Growth

Pictures of a Resent Dryout in Morrison Colorado Using the ELE 6400.

The Carpet, Walls and Contents Were Dried In Place

 

ELE 6400 Setup In drying Area

ELE 6400 in Drying Area with Air Movers and Downdraft Fan

Thermostat Controller and Humid Air being Exhausted Out the Window

Doorway Sealed to Drying Chamber

A Proud Member of the Emergency Restoration Network

Heat Drying Systems Distributed by Thermal Energy Drying System

A Dryout Last Summer at a Office Building in Evergreen Colorado

Using a ITA75 Drying System. It Dried Fast and

They got the Office Back to Normal in 30 Hours with No Major Repairs.

Heat provides the main source of energy to create evaporation. Adding air movement creates a synergistic effect which results in faster evaporation. Air exchange is a well known method for removing large quantities of moisture laden air fast and efficiently. We take an air-mover, connect lay flat ducting, vent the tube outside and remove moisture laden air much faster than you can remove the water from the air with a dehumidifier. A modest 2000 cfm heat drying system can exchange the air volume in a 2500sf building with 9’ ceilings once every 11 ¼ minutes. Air exchange is an integral part of most heat drying systems and air exchange can keep up with the fast evaporation rates heat drying produces.

 

Heat can dry structure without removing baseboard, tile cove base, cabinets, etc…

Heat penetrates deep into and through building materials drying areas that are not accessible. Intelligent venting, when necessary, requires little to no repair. Certain materials become irreversibly damaged when wet. Example: MDF or compressed paper baseboard. However, removing these damaged materials after drying, versus removal when wet, reduces the chance of unnecessary secondary damage. Dry it in place and reduce the chance for damage.

ITA 75 is a Heat Exchange Burner which Only Allows Heated Air Into the Structure. Heated Air Goes Through the 16” High Heat Hose in a Door and Into the Drying Area. The Clearer Hose is the Humid Air Being Exhausted Out.  The ITA 75 is Thermostatically Controlled.  This Allows Use Set the Desired Temperature  In the Drying Area and At the Same Time Help Prevent the Potential for Mold and Other Related Problems that Might Arise During the Drying Process

Exhaust Ducting Attached to a Airmover. This Allows Us to Exhaust the Humid Air Outside

Heated Air Into the Drying Area and Humid Air Exhausted Outside.

Because This Was a Office Building We Had To Use the Same Door for the Heated In and Humid Air Exhausted

ITA 75 is a Heat Exchange Burner which Only Allows Heated Air Into the Structure. Heated Air Goes Through the 16” High Heat Hose Across the Deck and Down Through a Window Well.  The ITA 75 is Thermostatically Controlled.  This Allows Use Set the Desired Temperature  In the Drying Area and At the Same Time Help Prevent the Potential for Mold and Other Related Problems that Might Arise During the Drying Process

Resent Dryout in Broomfield CO Using the ITA 75 Drying System

Basement Walls, Ceiling and Contents Needed Dried

Heat Down Through Window Well and Exhausted Out Front

Side of the House 

Exhaust Ducting Going Across the Room and Up Through the Basement Window

Exhaust Ducting Attached to a Airmover. This Allows Us to Exhaust the Humid Air Outside

Heated Air Blown Into the Wall Cavity. We Pulled the Baseboards and Drilled 1/2” Holes In the Walls. After Walls Were Dry the Only Repairs Needed

Were  Fill the Holes and Reinstall the Baseboards.

Exhaust Ducting Coming Out the Window  Well and Out Into the Yard. This is How the Humid Air is Removed from the Drying Area

Contact Us at:

303-674-8990 Evergreen

303-257-8056 Cell

E-mail: eric@247waterdamage.info

Web: www.ColorTechRestoration.com

 

Heated Air Ducted Through Window Well Into Drying Area

Cord To Thermostat In Drying Area

Color Tech Restoration

Air Movers Used to Move Heated Air in Drying Area

We Offer Portable Heat Drying Systems

As Well We Have Trailer Mounted Heat Drying Systems

ELE 6400

Eliminator

ITA &%

Pictures of a Resent Dryout in Frisco Colorado Using the ELE 6400.

The Carpet, Walls, Ceiling and Contents Were Dried In Place

 

Resent Dryout in Lakewood CO Using the Trailer Mounted Heat Drying System. Walls, Ceiling and Contents Needed Dried. Heat Was Ducted Down Through Window Well and Through Window In Upstairs Unit.

Upstairs Unit was Packed. Contents and Structure Were Dried In Place. We Heated from the Top and Bottom to Get Everything Dry. This Unit was Vacant.

Hot Air Was Ducted Into Ceiling Of Downstairs Unit which Helped Dry the Upstairs Unit from the Bottom.

Trailer Mounted Heat Drying System.

Heat Was Ducted Down Through Window Well and Through Window In the Upstairs Unit. This Allowed Us to Heat Dry Two Units at the Same Time.

Stairs to Downstairs Unit

Downstairs Unit

Heat Ducted to Downstairs Unit

Pictures of a Resent Dryout in Frisco Colorado Using the ELE 6400.

The Carpet, Walls and Contents Were Dried In Place.  Carpet, Walls and Contents Were Dry in 2 Days.

 

Our Large Heat Drying System. This Systems Allows Us to Dry Larger Areas or Dry Larger Homes with Ease.

Eliminator

Thermal Evaporative Accelerator